Question 1

How Can I Reset My Air Conditioner to Fix Power Issues?

Accepted Answer

Resetting an air conditioner to fix power issues means safely shutting off power to the system, waiting five minutes, then restoring power in the right order. Most power problems follow an outage or surge that trips a breaker or puts the compressor into a protective timeout. Give the system a true five‑minute “compressor timeout”; cutting it short can keep the unit locked out. Our certified technicians arrive in fully stocked trucks, so most repairs can be completed on the same visit. We handle many post‑storm resets across the Columbus area and can test for loose connections or weak capacitors if it trips again. Try this simple reset procedure: * Set the thermostat to Off. * Turn the AC/HVAC breakers Off (and pull the outdoor disconnect if present); wait 5 minutes. * Turn breakers and disconnect On, then set Cool, Auto fan, and lower the setpoint. * Stop and call a pro if the breaker trips again, you smell burning, or hear loud buzzing. If the breaker keeps tripping or you hear humming without the fan, stop trying to reset and schedule service to prevent equipment damage.
Updated: 2026-06-19
Need help in Columbus, IN? Call 317-830-5862 or book online.

Question 2

Why Is My Air Conditioner Not Turning On Despite Thermostat Set to Cool?

Accepted Answer

An air conditioner that won’t turn on with the thermostat set to Cool usually indicates a power, control, or safety lockout problem. The most common culprits are incorrect thermostat settings or dead thermostat batteries, followed by a tripped breaker or a condensate safety switch that shut the system down to prevent water damage. If the unit was just powered off, many systems impose a 3–5 minute restart delay to protect the compressor. Around our Trafalgar service calls, we often find a small algae plug in the drain pan float switch that silently stops the system. Try these quick checks before calling: * Set thermostat to Cool, Fan Auto, and drop the setpoint at least 5°F below room temp. * Replace thermostat batteries and confirm the date/time isn’t in a schedule Hold. * Check the furnace/air handler switch, outdoor disconnect, and the AC breaker; reset once only. * Inspect the air filter; a severely clogged filter can trigger safety limits. * Look for water in the indoor unit pan; a tripped float switch means the drain is clogged. If a breaker trips again after one reset, leave it off and book service to avoid equipment or wiring damage.
Updated: 2026-06-05
Need help in Trafalgar, IN? Call 317-830-5862 or book online.

Question 3

What should I do if my HVAC system needs emergency repair now?

Accepted Answer

If your HVAC system needs emergency repair now, turn the system off and call Johnson Heating, Cooling, and Plumbing for rapid diagnostics and same-visit repairs. Most sudden no-heat or no-cool calls trace to failed start components, safety lockouts, or a clogged drain, which are parts our stocked trucks typically carry. Our Fixed Right, or It's Free guarantee covers completed repairs for six months, giving calm backup while we get you running. We help homeowners around the Trafalgar area stabilize systems quickly without guesswork. Take these quick steps while you wait: * Set the thermostat to Off; if you smell burning or hear electrical arcing, switch the HVAC breaker Off. * If you smell gas, evacuate and call your gas utility from a safe place before contacting a technician. * If you see water around the indoor unit, power off the system and avoid the area; place a pan or towels if safe. * Do not keep restarting a unit that trips breakers or shuts down repeatedly. Have your model number and any error code ready to speed diagnosis.
Updated: 2026-05-28
Need help in Trafalgar, IN? Call 317-830-5862 or book online.

Question 4

Why Is My HVAC Not Heating Even Though It Turns On?

Accepted Answer

An HVAC system that turns on but does not heat usually points to an airflow restriction, thermostat/control error, or a fuel/electrical safety lockout. Most often the problem starts with a simple setting or blocked airflow that causes the furnace or heat pump to shut the heat off for protection. Technician note: a stuck heat-pump reversing valve can make vents feel cool even while the system runs. Around Franklin, our certified technicians arrive in fully stocked trucks to finish most repairs in one visit. Before you call, check these quick items: * Set the thermostat to Heat and raise the setpoint above room temperature. * Replace a dirty air filter and ensure vents are open. * Verify the furnace switch and breaker are on; reset once if tripped. * For gas heat, confirm the gas valve is open; for heat pumps, clear heavy ice from the outdoor unit. If you smell gas, see repeated breaker trips, or the unit short-cycles, turn it off and schedule a professional inspection.
Updated: 2026-05-22
Need help in Franklin, IN? Call 317-830-5862 or book online.

Question 5

What Is the Average Furnace Repair Cost for Homeowners?

Accepted Answer

The average furnace repair cost for homeowners varies by issue and is confirmed after an on‑site diagnostic; there isn’t a single “standard” price. Most costs stem from the specific part that failed and the labor time to test, access, and replace it. Many no‑heat calls trace to a dirty flame sensor or a failed igniter found with a quick meter check, while control boards and blower motors tend to be higher‑complexity fixes. We handle these diagnostics and repairs throughout the Lebanon area with honest, upfront pricing with no surprise fees. What drives repair price: * Part and labor: igniters, flame sensors, blower motors, or control boards need different parts and time * System age and warranty coverage for parts * Access limits, venting, or code updates that add labor * After‑hours or emergency timing If you smell gas, turn off the furnace and gas supply and contact a licensed technician immediately.
Updated: 2026-05-15
Need help in Lebanon, IN? Call 317-830-5862 or book online. “Ryan, Shawn, and Allen all did a great job with our repairs and eventual furnace replacement.” — Sam Marsh

Question 6

How much does same day HVAC repair typically cost?

Accepted Answer

Same day HVAC repair pricing is confirmed after an on-site diagnostic because the cost depends on the exact failure and parts needed. The biggest driver is which component failed and how much labor is required to restore safe operation. A technician insight: simple electrical parts can be quick; motor failures or refrigerant issues take more time because testing and setup matter. Our team serving the Mooresville area provides honest, upfront pricing with no surprise fees, and our certified technicians arrive in fully stocked trucks so most repairs can be completed on the same visit. Expect the diagnostic to determine these price factors: * Part type and availability (sensor, capacitor, motor, control board) * System type and size (AC, furnace, heat pump) * Refrigerant or combustion work requirements * Accessibility and after-hours timing * Any existing warranties on parts or labor Optional savings: $50 off AC system repair (cannot be combined or applied to the diagnostic; expires May 2026). Turn the system off if you smell gas, see smoke, or hear sparking and schedule a diagnostic for a precise quote.
Updated: 2026-05-07
Need help in Mooresville, IN? Call 317-830-5862 or book online.

Frequently Asked Questions

HVAC Repair